Fence Picket Calculator Guide: Board Sizing, Spacing, and Materials

Building a wood fence is one of the most rewarding DIY outdoor projects, but ordering mistakes are notoriously common. Because nominal 1x6 boards actually measure 5.5 inches wide, miscalculating board coverage can leave you short by 8% to 10% on pickets. This guide covers actual milled dimensions, post layout formulas, horizontal rail placement, and fastener recommendations for standard 4-foot and 6-foot fences.

Last updated: By MyHandyToolLab

Nominal vs. Actual Board Widths

When purchasing rough-sawn or surfaced lumber from home improvement centers, the printed "nominal" dimension reflects the green rough cut before planing and drying.

Nominal LabelActual Milled WidthCoverage per Linear Foot (Privacy)
1x4 Picket3.50 inches (89 mm)3.43 pickets / ft
1x6 Picket5.50 inches (140 mm)2.18 pickets / ft
5/4x6 Deck Board5.50 inches (140 mm)2.18 boards / ft
2x4 Rail1.5" × 3.5" (38 × 89 mm)Horizontal framing
4x4 Post3.5" × 3.5" (89 × 89 mm)Vertical structural post
Always calculate picket requirements using 5.5 inches rather than 6.0 inches. Dividing a 100-foot run by 6 inches yields 200 boards, whereas the actual 5.5-inch boards require 219 boards—leaving you 19 pickets short!

Gap Spacing: Privacy vs. Decorative Picket Fences

The gap spacing between pickets directly controls visibility, airflow, and lumber requirements:

  • 0-Inch Gap (Privacy): Boards touch edge-to-edge. Ideal for backyard privacy, pets, and security. Requires roughly 2.2 pickets per linear foot.
  • 0.5-Inch to 1.0-Inch Gap (Semi-Privacy): Allows wind to pass through during storms while dampening direct sightlines. Reduces wind pressure on posts.
  • 1.5-Inch to 2.5-Inch Gap (Traditional Picket): Classic front-yard decorative fencing. Maximizes curb appeal and cuts board costs in half.

Post Spacing and Horizontal Rail Engineering

Standard residential wood fences use 8-foot (96-inch) post-to-post spacing. For structural longevity, post holes should be dug to at least 1/3 the total post length (or below your local winter frost line) and anchored with commercial concrete mix.

Horizontal 2x4 framing rails prevent pickets from sagging, twisting, and bowing:

  • 4-Foot High Fence: Requires 2 horizontal rails per 8-foot bay (installed ~6" from top and bottom).
  • 6-Foot High Fence: Requires 3 horizontal rails per 8-foot bay (top, center, and bottom).
  • 8-Foot High Fence: Requires 4 horizontal rails and heavy 6x6 posts to resist wind loads.

Exterior Fasteners and Screws

Never use standard drywall or interior zinc screws for outdoor fencing. Tanni acids in western red cedar and copper preservatives in pressure-treated pine rapidly corrode standard steel screws, causing black staining and structural failure.

Use 1-5/8" or 2" exterior polymer-coated deck screws or Grade 305 stainless steel screws. Fasten each picket with 2 screws at every horizontal rail (6 screws total per picket on a standard 6-foot fence).

Ready to try it?

Open the Fence Picket Calculator and follow the steps above.

Open tool

Related tools and guides

Frequently asked questions

How many pickets do I need for a 100-foot privacy fence?

A 100-foot fence (1,200 inches) using standard 5.5" wide pickets requires 219 pickets. Adding a 10% safety margin for warping and cut ends brings the recommended purchase order to 241 pickets.

Should pickets touch the ground?

No. Pickets should be installed with a 1-to-2-inch gap above the ground line. Ground contact causes wood to wick moisture from soil and grass, accelerating fungal rot.