Cabinet Pull Placement Chart: Sizes, Heights & Spacing Standards
Selecting the correct cabinet pull size and determining its exact drilling height depends on cabinet door height and drawer width. Designers follow the "rule of thirds" — a pull should ideally span approximately one-third of the drawer or door width for balanced proportion and ergonomic comfort.
Cabinet Door Pull Placement Chart by Height
For wall and base cabinet doors, hardware placement is measured from the bottom corner (upper cabinets) or top corner (base cabinets) opposite the hinges:
| Cabinet Door Height | Door Type | Recommended Pull Size | Bottom/Top Corner Offset | Horizontal Inset |
|---|---|---|---|---|
| Under 24 inches | Small Upper / Valance | 3" (76mm) or 96mm (3.78") | 2.0" to 2.5" | Centered on stile (1"-1.125") |
| 30 inches | Standard Upper Door | 96mm (3.78") or 128mm (5.04") | 2.5" | Centered on stile (1.125") |
| 36 inches | Tall Upper Door | 128mm (5.04") or 160mm (6.30") | 2.5" | Centered on stile (1.125") |
| 42 inches | Ceiling-Height Upper | 160mm (6.30") or 192mm (7.56") | 2.5" to 3.0" | Centered on stile (1.125") |
| 30 inches (Base) | Standard Base Door | 128mm (5.04") or 160mm (6.30") | 2.5" from top | Centered on stile (1.125") |
| 60 to 84 inches | Pantry / Tall Utility | 192mm (7.56") to 12" Appliance Pull | Center at 36" floor datum | 1.25" to 1.5" from edge |
Drawer Front Pull Size & Count Chart by Width
For drawers, the width of the drawer front dictates whether a single centered handle or dual handles are required:
| Drawer Front Width | Pull Count | Recommended Pull C2C Length | Placement Spacing | Vertical Alignment |
|---|---|---|---|---|
| 12" to 15" (Narrow) | 1 Pull | 3" (76mm) or 96mm (3.78") | Exact center (W ÷ 2) | Center (Height ÷ 2) |
| 16" to 21" (Standard) | 1 Pull | 96mm (3.78") or 128mm (5.04") | Exact center (W ÷ 2) | Center (Height ÷ 2) |
| 22" to 27" (Medium) | 1 Pull | 128mm (5.04") or 160mm (6.30") | Exact center (W ÷ 2) | Center (Height ÷ 2) |
| 28" to 33" (Wide) | 2 Pulls (or 1 Long) | Two 128mm Pulls OR One 8"-10" Pull | Pulls centered at 1/4 and 3/4 | Center or Upper Third |
| 34" to 42" (Extra Wide) | 2 Pulls (or 1 Appliance) | Two 160mm Pulls OR One 12" Pull | Pulls centered at 1/4 and 3/4 | Center or Upper Third |
The 1/3 Rule of Thumb
Metric (mm) to Imperial (Inches) Conversion Table
Modern cabinet hardware manufactured in Europe and Asia follows metric millimeter hole centers. If you purchase hardware online, the product listing might give dimensions in fractional inches that round off true millimeter drill spacing. Always drill using the true millimeter center distance:
| Metric C2C | Decimal Inches | Closest Fraction | Common Hardware Application |
|---|---|---|---|
| 64 mm | 2.520" | 2-1/2" | Vintage bin pulls & small spice drawers |
| 76.2 mm | 3.000" | 3" Exact | Traditional US standard pulls |
| 96 mm | 3.780" | 3-3/4" | Standard upper door and cutlery drawer handles |
| 128 mm | 5.039" | 5-1/16" (called 5") | The most popular modern kitchen pull size |
| 160 mm | 6.299" | 6-5/16" | Medium drawers & tall wall cabinets |
| 192 mm | 7.559" | 7-9/16" | Deep pot drawers & large pantry doors |
| 224 mm | 8.819" | 8-13/16" | Modern oversized horizontal drawers |
| 256 mm | 10.079" | 10-1/16" | Long single-pull drawers |
| 320 mm | 12.598" | 12-5/8" | Appliance pulls & integrated refrigerators |
4 Critical Placement Verification Steps
- Rule 1: Never measure from the floor to align upper cabinets. Ceiling and floor dips (often 1/2" across a 10-foot run) will make straight handles look wavy. Always measure from the cabinet door bottom.
- Rule 2: Mount hardware after countertop installation. Countertop overhangs (standard 1.5") shade the top drawer. Seeing the shadow line ensures handles aren't hidden.
- Rule 3: Beware of corner corner-cabinet clearance. Knobs and pulls on corner cabinets can collide when adjacent doors open simultaneously. Use knobs with projection under 1 inch in tight inside corners.
- Rule 4: Double check drill bit size. #8-32 machine screws need a 3/16" hole. A 1/8" hole is too small and will strip the wood threads, while a 1/4" hole will allow the screw head to slip through.
Ready to try it?
Open the Open Cabinet Hardware Placement Calculator and follow the steps above.
Related tools and guides
Frequently asked questions
What is the most popular kitchen cabinet pull size?
The 128mm (approx 5-inch) center-to-center pull is currently the most popular hardware size for residential kitchens. It fits standard drawers and doors while offering full 4-finger hand clearance.
Should base cabinet pulls be higher or lower?
Base cabinet pulls should be placed near the top corner of the door (2.5 inches down from the top edge). Placing them too low forces you to bend down unnecessarily every time you open a cabinet.