Standard Cabinet Handle Sizes: Center-to-Center Dimensions & Buying Guide

Cabinet handle sizes are measured by Center-to-Center (C2C) spacing β€” the exact distance between the centers of the two screw holes, not the total overall length of the handle. The most common standard cabinet handle sizes in modern kitchens are 96mm (3-3/4"), 128mm (5"), 160mm (6-5/16"), and traditional 3-inch (76.2mm) pulls.

Last updated: By MyHandyToolLab

What Center-to-Center (C2C) Means vs. Overall Length

When shopping for replacement cabinet hardware, confusing Center-to-Center (C2C) distance with Overall Length is the single most common reason homeowners order the wrong size:

  • Center-to-Center (C2C): The distance between the center of the left screw hole and the center of the right screw hole. This is the only measurement that matters for drilling holes or replacing existing handles.
  • Overall Length: The total tip-to-tip length of the handle bar. On bar pulls with end extensions, the overall length can be 1.5" to 2.5" longer than the C2C measurement.
  • Projection: How far the handle sticks out from the cabinet face (standard is 1.25" to 1.5"). Ample projection is critical for comfortable finger clearance.

How to Measure an Existing Handle

Remove the handle from your cabinet door. Measure from the center of one screw hole to the center of the other on the backside using a millimeter ruler. If it measures approximately 3-3/4 inches, it is almost certainly a 96mm pull. If it measures 5 inches, it is a 128mm pull.

Standard Cabinet Handle Sizing Matrix

Here is the complete reference table of industry standard pull sizes, their common names, and typical cabinetry applications:

Size (mm)Size (Inches)Common NameBest Cabinet ApplicationErgonomic Finger Grip
76.2 mm3.000"3-Inch PullTraditional builder grade & older kitchens2 to 3 fingers
96 mm3.780"3-3/4" PullStandard upper wall doors & small drawers3 fingers
128 mm5.039"5-Inch PullStandard base doors & medium drawersFull 4-finger hand grip
160 mm6.299"6-5/16" PullWide base doors & 24"-30" drawersSpacious 4-finger grip
192 mm7.559"7-9/16" PullDeep 30"-36" drawers & tall pantry doorsHeavy-duty 2-hand or wide grip
224 mm8.819"8-13/16" PullContemporary horizontal slab drawersArchitectural multi-finger
305 mm12.000"12-Inch PullAppliance pulls (dishwashers, sub-zero fridges)Heavy appliance rated

How to Choose the Right Size for Your Kitchen

A common design dilemma is whether to use a single uniform handle size throughout the entire kitchen or mix multiple lengths:

  • Option A: Uniform Single Size (Most Cost-Effective): Using 128mm (5") pulls across all doors and drawers creates a cohesive, clean look. You only need one drilling jig setting and can purchase hardware in bulk.
  • Option B: Proportional Sizing (Designer Standard): Use 96mm pulls on short upper doors and top cutlery drawers; 128mm pulls on standard base doors; and 160mm or 192mm pulls on deep lower drawers. This maintains scale with larger panels.
  • Option C: Knobs on Doors, Pulls on Drawers (Classic Transitional): Knobs on all vertical swinging doors, and pulls on all horizontal pulling drawers.

Ready to try it?

Open the Open Cabinet Hardware Calculator and follow the steps above.

Open tool

Related tools and guides

Frequently asked questions

Is 3-inch or 96mm the same size?

No. A 3-inch pull has 76.2mm hole spacing. A 96mm pull is 3.78 inches (almost 3-3/4"). They are not interchangeable without re-drilling and patching one hole.

What is the standard screw thread for cabinet hardware?

In North America, almost all cabinet knobs and pulls use #8-32 machine screws. European imports occasionally use metric M4-0.7 screws.